1 Agitator vessel in stainless steel, free standing on 4 feet, with adjusting screws

• Total capacity ca.: 420 l

• Supplies: 1 rest outlet (bottom middle) NW 25 G with curve 90 degree
                       and outlet pipe going to the rim of the vessel NW 25 KM 
                   1 supply on top NW 40 G for CIP sprayhead

• ca. size: diam. inside = 0,79 m            diam. outside = 0,80 m
                 D inside = 0,89 m                 H vessel = 0,80 m
                 H agitator motor = 0,29 m
                 H total = 1,80 m 

• Agitator motor: make Turbo Müller, 1,6 kW, 1.410 rpm, insulation class E
                             (motor overhauled)

• Wave agitator: diam. = 40 mm / L = 0,72 m

• Agitator wing: diam. = 165 mm with 3 "wings" and outer ring (turbo wing)

• Lid: 1/2 openable lid

• CIP: ?

• Internal number (Please include with all questions/orders!!): R03/03

• Photo

Back to the top

2 Agitator vessels in stainless steel, insulated, free standing on 3 VA feet

• Make: Georg Dorner Nürnberg
• Total capacity ca. 1.600 l each
• Useable capacity: ca. 1.500 l each
• Built: 1984
• ca. size: diam. outside = 1,30 m / diam. inside = 1,19 m / H total = 2,20 m / D inside = 1,45 m
• Insulation: outdoor insulation, riveted at the bottom, strength ca. 50 mm
• Agitator: make Turbo Müller
                  motor: 1.380 rpm / 0,55 kW, 380 volt, 0,5 ampere,  insulation class B
                  wave: stainless steel, diam. 30 mm / L up to 200 mm over bottom
                  wing: 2-wings, W total = ca. 130 mm
• Supplies: 1 rest outlet NW 50 KM
• Heating: vessels are prepared for electrical heating coil. Previously with heating coil, but they were all damaged 
                  during the dismantling. 
• Lid: ca. 1/3 openable via hand lever / rest welded shut
• Height meter: via plastic pipe with closing cock and rest outlet cock
• Bottom: flatconical
• Feet: 3 feet, 2 of them with adjusting screws and ground plates
• Misc.: each vessel has an ladder holder.
• Remark: the vessel with the "number 6" has a defect agitator motor (please ask about the special price)
                  the motor of the second vessel is in working order.
                  one of the agitator vessels has a larger dent in the outer sheet metal of the insulation because of dismatling,
                  please ask for photos. The vessels itself are not affected by this.
• Internal number (please include with all questions/orders!!): R10/05
• Photos

Back to the top

1 Agitator vessel in stainl. steel, heat- and coolable, insulated
(there´s an option at the moment)

• Total capacity: ca. 3.500 l
• Manufacturer: Ahlborn
• Size: diam. = 1,78 m / H with agitator = 4,10 m
• Supplies: below: rest outlet NW 80 G + clear outlet NW 80 G (in frame below)
                  sideways: cooling supplies inlet below NW 50 and outlet on top NW 65
                  on top: 2 x NW 40 with 2 sprayheads / 1 x NW 65 G for filling inlet /
                              1 aeration dome with cover and condensation tube, diam. 150 mm
• Lid: dome lid on top, closeable, diameter 455 mm
• Bottom: conical towards outlet
• Agitator: Stelzer agitator with adjustable transmission with 2,2 kW at 10 - 50 rpm, Typ DRG6R
                  wave lenght = 1.860 mm (with 2 propellers with a diameter of 700 and 900 mm)
• Remark: the tank was used to stir Kieselguhr - the layer on the inside should therefore be easily removable.
                  the tank also has some slight dents.
• Internal number (Please include with all questions/orders!!):  R19/001
• Photos

Back to the top

Back to the top

Back to the selection

---

Copyright © 2002 Albin Halbritter GmbH. All rights reserved.
updated: 12. Mai 2023